Articles

How to Apply a dbrand Razer Blade Skin

July 29, 2019



if you just got your D brand razor blade skin relaxed this is going to be easy first wipe your device free of dust and fingerprints for optimal results ensure you are under bright lighting note that your D brand skin comes with up to four elements top bottom palm rest and trackpad you will require a hairdryer for this installation so pause the video now and go grab one welcome back don't worry if your exact laptop isn't shown the procedure is nearly identical for all razor blade models let's start with the top skin note that in order to ensure the skin doesn't peel up over time it is designed to be slightly smaller than the surface of your blade once you've completed installation you'll see that there is uniformly equal spacing between the border of the skin and the edge of your laptop to begin remove the skin from the 3m paper and reattach as shown before laying the skin down make sure the Razer logo is oriented properly align the skin along the top and right edge less than half a millimeter from the border take a look at the three exposed corners you should see equal spacing between the border of the skin and the edge of the laptop on all sides if you align the skin flush against the edge of the laptop you'll see that the opposite side will be too short if the spacing isn't equal on all edges simply tear it off and start again once lined up flawlessly apply pressure to the exposed portion next shift the 3m paper down diagonally by about two inches and apply pressure to the exposed portions repeat this process until the entire top surface has been applied you if you are applying a no logo version of the skin briefly heat up the logo area and apply firm pressure to get a clean Razer logo silhouette depending on your razor blade model the corners will either be flat or rounded if your laptop has flat corners skip ahead to the time shown on screen if the corners of your laptop are rounded let's take a minute to apply the skin properly to form the skin around the rounded edge pick a corner then peel it back next grab your hairdryer and briefly heat the corner apply firm pressure to ensure it stays stuck over time repeat this process for the other three corners next up is the bottom piece remove the skin and reattach our shown a line around the Fed cutouts ensuring that they are centered properly once lined up apply pressure to the exposed portion leaving the corners unstuck next lift the skin and shift it down to expose the remaining vent cutouts now apply pressure to secure the skin in place shift the paper down once more stopping just short of the rubber foot once aligned apply pressure to the exposed portion next rotate your device and remove the 3m paper entirely you may now smooth out the portion below the rubber foot next position the skin around the – setter screws you may now apply pressure toward the edge of the device bit by bit leaving the corners unstuck applying pressure in any other way may result in wrinkles if you the whole thing up don't worry just peel back the skin as shown you will likely find that the skin has been stretched let's take a moment to fix that lay down the deformed skin and grab your hairdryer hold the skin down from one corner and heat it up for 10 to 15 seconds once complete you should find that the skin has returned to its original shape you may now lift the skin and try again finally peel back any of the four corners grab your hairdryer and heat it up once heated apply firm pressure to secure the skin in place repeat for the remaining three corners let's now install the palm rest remove the skin from the 3m paper and reattach as shown make sure to peel the skin gently otherwise the cutouts may not remove alongside the skin a line around the border of the device insuring the skin is perfectly straight along the hinge once lined up flawlessly apply pressure to the exposed portions next shift the 3m paper to the left and apply pressure to the right side once smooth down remove the speaker cut out using the peel tab apply firm pressure along the left side of the speaker and removed the keyboard cut out entirely you may now shift the 3m paper to the left and apply pressure to the exposed portion continue this process until the entire palm rest skin has been applied next remove the trackpad and left speaker cutouts apply one more round of pressure to ensure the skin is secured in place to install the razor trackpad use a razor done if you have any questions you know how to reach us

14 Comments

  • Reply dekaaizer July 29, 2019 at 2:57 pm

    The fact that this video has no dislikes and an insane amount of people watching it is kinda scary to me.

  • Reply Mohit Choudhary July 29, 2019 at 2:57 pm

    8:00 Instructions Unclear.
    Chöpped my PP off.

  • Reply Mohit Choudhary July 29, 2019 at 2:57 pm

    Make skin for my armpits please

  • Reply Mt. Exploding July 29, 2019 at 2:57 pm

    If you buy me a razor blade I will buy one of your skins

  • Reply Parsons Jin July 29, 2019 at 2:57 pm

    remember the skin for airpower they got ? lol Genius team

  • Reply keppy July 29, 2019 at 2:57 pm

    Potater

  • Reply Anirudh Venkatachalam July 29, 2019 at 2:57 pm

    Make skins for HP Envy x360 pls

  • Reply TheGodPotato July 29, 2019 at 2:57 pm

    Yes I'm here

  • Reply Dhrumin Patel July 29, 2019 at 2:57 pm

    mmm… potato

  • Reply Immortality July 29, 2019 at 2:57 pm

    Potati?

  • Reply Manjot singh July 29, 2019 at 2:57 pm

    Potatoes

  • Reply Rikhil Pabari July 29, 2019 at 2:57 pm

    Or potato

  • Reply Der Baumann July 29, 2019 at 2:57 pm

    Instructions unclear
    Ended up buying iphone xs

  • Reply iShoTz July 29, 2019 at 2:57 pm

    potato

  • Leave a Reply